饱和块状混合回填土地基的一维固结分析

用块状渣土置换软弱地基和回填低洼谷地等是处置工程渣土的有效途径。为了分析饱和块状混合回填土地基的固结性状，运用混合物理论建立了其一维固结模型。首先，假定块状土固相和充填土固相之间满足等应变条件，获得了饱和块状混合回填土中各相应变与块状土孔隙变形和充填土孔隙变形的关系式。其次，在小应变条件下，根据自由能势函数方程建立了饱和块状混合回填土的一维线弹性本构方程，再结合达西定律和应力平衡方程获得了一维固结控制方程。再次，利用分离变量法得到一维固结解析解，通过退化本文模型与已有模型进行对比，验证了本文模型的正确性。最后，基于所得解析解，分析了充填土孔隙渗透系数、块状土孔隙渗透系数以及流体交换参数等因素对饱和块状混合回填土地基固结性状的影响。分析结果表明：充填土孔隙渗透系数对饱和块状混合回填土地基整体固结性状起主导作用；在固结初期，块状土超孔压会有一定程度的上升，且3个参数具有相似的作用机理。     

超高分子量聚乙烯纤维增强中空蜂窝模压复合材料性能研究

为研制车船等壳体所用的轻质、高强复合板材,选用超高分子量聚乙烯(UHMWPE)短纤维纱,制备成单层经纬为120根/(10 cm)的平纹组织,采用多组经纱持续更替交织层的方法制成2L(1+0)型、4L(2+1)型、6L(3+2)型3种多层角联锁结构织物,采用扦插芯棒、模压成型方法制成菱形蜂窝状的热固性环氧树脂基中空板,并与2块真空吸液法制成的面板组成“三合一”复合板,同时测定了复合板材的结构特征及其平拉、平压和弯曲性能。结果表明:3种类型复合板的密度均远小于水的密度,其中6L(3+2)型最小,为0.48 g/cm³;复合板层数越多,环氧树脂越难渗透尤其是在中空板菱形交叉点处,复合板平拉、平压、抗弯曲强度则呈现递增,制成的6L(3+2)型复合板试样平压强度可达到1.03 MPa。     

Cloning,sequencing and structural analysis of membrane-bound polyphenol oxidase from Granny Smith apples (Malus × domestica Borkh)

The gene sequence coding for the membrane-bound polyphenol oxidase (mPPO) with a length of 1761 bp was cloned by PCR method and shown to contain one highly conserved sequence encoding a di-copper-binding region. The predicted three-dimensional structure of mPPO indicated that the active site was located near two copper ions and composed of a typical bundle of four α-helices. Each of the two catalytic copper ions was coordinated with three histidine residues in the hydrophobic pocket, yielding His 180, His 201, His 210, His 332, His 336 and His 366. Docking studies showed that 4-methylcatechol and chlorogenic acid have different binding models due to different ligand sizes and binding sites in the active centre, and it was found that the smaller compound exhibited a higher affinity for mPPO. Molecular dynamic simulation results indicated that Phe 353 is important in controlling enzymatic activity through influencing substrate coordination in the active site.     

Observation of table-like magnetocaloric effect and large refrigerant capacity in Nd6Fe13Pd1–xCux compounds

The table-like magnetocaloric effect is significant for the magnetic refrigeration applications above 20 K based on the Ericsson cycle. Herein, we prepared a series of Nd₆Fe₁₃Pd_1–xCu_x (x = 0.05, 0.1, 0.15) compounds by the arc-melting method. These compounds show the single crystalline phase in the tetragonal Nd₆Fe₁₃Si-type structure with the space group I4/mcm. A magnetic phase transition from ferromagnetism to antiferromagnetism and a metamagnetic transition from the antiferromagnetic state to the ferromagnetic state are observed in each of the compounds. The compounds exhibit table-like magnetocaloric effects with large refrigerant capacities. A constant ΔS_M in a temperature span of 40 K in the Nd₆Fe₁₃Pd_0.85Cu_0.15 compound are observed. For a field change of 0–5 T, the peak values of –ΔS_M for the Nd₆Fe₁₃Pd_0.95Cu_0.05, Nd₆Fe₁₃Pd_0.90Cu_0.10, and Nd₆Fe₁₃Pd_0.85Cu_0.15 compounds are estimated to be 4.8, 4.6 and 4.4 J/(kg·K) with corresponding refrigerant capacity values of 323, 331 and 316 J/kg, respectively. The obtained table-like magnetocaloric effects with large refrigerant capacities as well as fairly small thermal and magnetic hysteresis deem these series of compounds good candidates for single-phase magnetic refrigeration based on the Ericsson cycle.     

基于BIM超高层密集布筋区埋入式型钢混凝土柱脚施工技术

以漳州市某超高层项目为例,针对超高层密集布筋区埋入式型钢柱脚与钢筋的深化设计、地脚螺栓的定位预埋、型钢柱脚支撑体系设计、节点钢筋穿插连接施工、埋入式型钢柱脚安装等方面,提出切实可行的施工方法,解决了埋入式型钢混凝土柱脚的地脚螺栓精准预埋、与底板密集钢筋穿插连接施工、悬空支撑稳定等一系列施工技术难题,既满足了设计方案的要求,又可为类似工程提供借鉴。     

“方变圆”变径筒状结构滑模施工技术

为解决塔式光热的核心构筑物吸热塔"方变圆"变径超高筒体结构施工难题,选用一套可变形的滑模平台系统,通过操作系统上可调千斤顶支座、门架横向液压千斤顶装置、多处可调节模板角度和收缩模板的丝杆等,使得滑模根据施工需求可在一定的范围内调节模板倾角、间距,并逐步完成收缩变形,其理论滑模允许偏角20°,最终高效完成异形结构施工。该滑模系统刚度大、承载及堆料能力强、空间大、机械化程度高,施工操作简单,安全性高,适应沙漠极端环境。全过程仅需使用一套滑模体系,就能完成方形段、方变圆的变形段及圆形段施工,大大提高了施工效率,为类似环境下相似结构的施工提供了一定的参考。     

Electrochemical performance of in situ LiFePO4 modified by N-doped graphene for Li-ion batteries

LiFePO₄ modified by N-doped graphene (NG) with a three-dimensional conductive network structure was synthesized via a one-step in situ hydrothermal method. The effects of N amount of NG on the phase structure, morphology, and electrochemical properties of LiFePO₄ are investigated in this study. X-ray diffraction (XRD) results show that doping suitable N amounts in NG do not alter the crystal structure of LiFePO_4, and scanning electron microscopy (SEM) images show that NG can slightly reduce the particle size of LiFePO₄. The high-resolution transmission electron microscopy (HRTEM) results show that the LiFePO₄ particles are well covered and connected by NG. The electrochemical performance confirms that LiFePO₄ modified by 20% N-doped graphene (named LFP/NG-4) displays a perfect specific capacity of 166.6 mAh·g^?1 at a rate of 0.2C and can reach 125 mAh·g^?1 at a rate of 5 C. Electrochemical impedance spectroscopy (EIS) results illustrate that the charge transfer resistance value of the LFP/NG-4 composite is only 58.6 Ω, which is very low compared with LiFePO₄. Cyclic voltammetry (CV) tests indicate that the addition of 20% N-doped graphene can effectively reduce electrode polarization and improve reversibility. The LFP/NG-4 composite with a three-dimensional conductive network structure can be regarded as a promising cathode material for Li-ion batteries.     

Microstructural and mechanical properties assessment of transient liquid phase bonding of CoCuFeMnNi high entropy alloy

The transient liquid phase (TLP) bonding of CoCuFeMnNi high entropy alloy (HEA) was studied. The TLP bonding was performed using AWS BNi-2 interlayer at 1050 °C with the TLP bonding time of 20, 60, 180 and 240 min. The effect of bonding time on the joint microstructure was characterized by SEM and EDS. Microstructural results confirmed that complete isothermal solidification occurred approximately at 240 min of bonding time. For samples bonded at 20, 60 and 180 min, athermal solidification zone was formed in the bonding area which included Cr-rich boride and Mn₃Si intermetallic compound. For all samples, the γ solid solution was formed in the isothermal solidification zone of the bonding zone. To evaluate the effect of TLP bonding time on mechanical properties of joints, the shear strength and micro-hardness of joints were measured. The results indicated a decrement of micro-hardness in the bonding zone and an increment of micro-hardness in the adjacent zone of joints. The minimum and maximum values of shear strength were 100 and 180 MPa for joints with the bonding time of 20 and 240 min, respectively.     

Comparison between fluctuation of floating potential gradient and velocity of blob structure on HL-2A tokamak

Several results based on the Langmuir probes' data on the HL-2A tokamak are presented. The blob structures' radial and poloidal drift velocities, estimated by the gradient of floating potential and by time delay evaluation, are compared in different line-averaged density and electron cyclotron resonance heating conditions. A positive correlation is observed in the comparison between blobs' radial velocity estimated by the two methods mentioned above, regardless of the situation differences mentioned above. Correlation is also observed in the comparison between the blobs' poloidal velocity estimated by the two methods in different situations, while a shift due to the different line-averaged density is observed. These results imply that the radial gradient of floating potential may have some value as a reference during data analysis in low-parameter discharge.